[WTB] - KL"DE" Engine

Bling Bling · Post by **Bling Bling** » November 15th, 2005, 10:24 pm

I live in the Calgary area. I have spoken to Rick J and he has given some places to look but I thought I would ask if anyone has a buddy or themself owns a car with the above engine in it. Preferably lower K's but must have ECU and VAF sensor. Please get back to me.

I'm hoping to get one rebuilt and installed in my car before Spring if possible.

deathman · Post by **deathman** » November 16th, 2005, 2:56 am

i have a kl 2.5 i rebuilt 2000 miles ago. i could break it down & ship it to you in 4-5 boxes. heres the but, it burns oil like crazy. i guess the machine shop honed it to far, so you would have to have it bored out with new pistons & ring. there is a sell on probetalk for new forged h-beam rods that are made to use aftermarkit piston's. i thought about doing this myself, but no money.

the motor was completly rebuilt, all was new 2000 miles ago
all seal's, bearing's, timing set, oil pump,
i had the heads rebuilt also, i ported & polished the runners myself, lots of time spent.

to reassemble all you would have to do is bore it like i said above, get a head gaskit, everhting else is done.

i was going to use it for raceing, so i but alot of time into this motor. the only thing i didn't check myself was the piston's & block (payied the machince shop to do it, they let me down)

parts alone cost me over $700.00 then the machine work (head & block 400 euro) & my time i hate to think what i would lose.

make me a offer

johnnie

deathman · Post by **deathman** » November 16th, 2005, 2:57 am

i have a ecu, but no vaf

Bling Bling · Post by **Bling Bling** » November 16th, 2005, 10:55 am

Sounds great but after shipping it here from Germany I think it would cost too much. But it sounds like you rebuilt it the same way I was going to.

deathman · Post by **deathman** » November 16th, 2005, 11:57 am

NO SHIPPING WOULD ONLY BE $120.00 I WOULD BREAK IT DOWN INTO 60LB BOXES. GIVE ME A ZIP & I COULD GIVE YOU A BETTER EST.

Bling Bling · Post by **Bling Bling** » November 16th, 2005, 6:01 pm

That's ok. But what are you asking for your engine and how much money would be required to install the new hardware?

deathman · Post by **deathman** » November 16th, 2005, 11:55 pm

i was thinking about $800.00, BUT DO YOU HAVE a friend in the states i could send it to, customs would kill you

bulaian · Post by **bulaian** » November 17th, 2005, 9:41 am

you cannot send directly from germany to canada?

deathman · Post by **deathman** » November 17th, 2005, 11:36 am

i can but customs might kill you, or delay the shipment, if you want to buy it i will ship it anyway you like.

bulaian · Post by **bulaian** » November 17th, 2005, 1:06 pm

why would customs kill us in Canada but not when you ship to the US?

deathman · Post by **deathman** » November 17th, 2005, 1:56 pm

well because i work for the U.S. gov., so it's like i am in the states (new york) when i mail something. it just about 5-8 extra days for mail to come & go

deathman · Post by **deathman** » November 17th, 2005, 1:57 pm

well because i work for the U.S. gov., so it's like i am in the states (new york) when i mail something. it just about 5-8 extra days for mail to come & go