Carbon fiber Tails.
-
Tyler17rose
- Regular Member
- Posts: 846
- Joined: October 19th, 2002, 2:01 am
- Location: Ottawa, Ontario, Canada
- Contact:
Carbon fiber Tails.
They look different then the other ones that were posted...<p>Tails
Mods:
- ZE, Mike seli 214 intake cams, Ported n polished heads, Interprep valve springs, DE retainers, rebuilt bottom end, toga main and rod bearings, toga hv oil pump, CZT 67mm tb, mbx udp, ported intake mani, SS headers, 2.5inch full exhaust, racingbeat muffler, highflow cat, megasquirt v2.
new toy, 86 TII rx7, JDM S5 motor/turbo, + alot of other goodies
- ZE, Mike seli 214 intake cams, Ported n polished heads, Interprep valve springs, DE retainers, rebuilt bottom end, toga main and rod bearings, toga hv oil pump, CZT 67mm tb, mbx udp, ported intake mani, SS headers, 2.5inch full exhaust, racingbeat muffler, highflow cat, megasquirt v2.
new toy, 86 TII rx7, JDM S5 motor/turbo, + alot of other goodies
-
papa roached
- Senior Member
- Posts: 2761
- Joined: December 10th, 2002, 2:01 am
- Location: Montgomery, WVa
Re: Carbon fiber Tails.
or a better pic, them are sweet
93 MX-3 GS (collecting parts for Eunos Presso conversion), 94 626 Transmission (4.10 gears), KL31 camed KL-ZE, Millenia intake, Millenia TB, SSAutochrome V2 headers, Magnaflow cat, 2 1/4 in pipe, Top Speed Pro 1 muffler, 9lb Fidanza Flywheel, ACT clutch, Corksport SS clutch line, Corksport SS brake lines, Unorthadox UDP, 255 lph fuel pump, HEI mod, ghetto-charger intake, KL36 ECU, SRD transverse crossmember bushings, SRD shifter extention bushing, SRD crossmember, Corksport bronzoil shifter bushings, Brembo Crossdrilled and Slotted rotors, 15 inch Konig Heliums, ZX-2 S/R struts, Eibach lowering springs, OEM front strut bar, Ebay rear strut bar, BFGoodrich G-Force T/A KDWs
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
-
JasonH
- Regular Member
- Posts: 389
- Joined: March 16th, 2003, 2:01 am
- Location: Newark, DE, USA
- Contact:
Re: Carbon fiber Tails.
Yeah, better pic with better lighting.<p>Now I'm even more convinced that I would take the black over the carbon fiber. Unless maybe I had a carbon fiber rear spoiler.
-
papa roached
- Senior Member
- Posts: 2761
- Joined: December 10th, 2002, 2:01 am
- Location: Montgomery, WVa
Re: Carbon fiber Tails.
black whould look better over all on most cars, i know it would on mine, i like hte look of carbon fibre, but i have nothing to go with it
93 MX-3 GS (collecting parts for Eunos Presso conversion), 94 626 Transmission (4.10 gears), KL31 camed KL-ZE, Millenia intake, Millenia TB, SSAutochrome V2 headers, Magnaflow cat, 2 1/4 in pipe, Top Speed Pro 1 muffler, 9lb Fidanza Flywheel, ACT clutch, Corksport SS clutch line, Corksport SS brake lines, Unorthadox UDP, 255 lph fuel pump, HEI mod, ghetto-charger intake, KL36 ECU, SRD transverse crossmember bushings, SRD shifter extention bushing, SRD crossmember, Corksport bronzoil shifter bushings, Brembo Crossdrilled and Slotted rotors, 15 inch Konig Heliums, ZX-2 S/R struts, Eibach lowering springs, OEM front strut bar, Ebay rear strut bar, BFGoodrich G-Force T/A KDWs
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
-
fictionaldaydream
- Regular Member
- Posts: 805
- Joined: April 19th, 2002, 2:01 am
- Location: OKC, Oklahoma
Re: Carbon fiber Tails.
They look better then from the other picture.
-
monstar-mx-3
- Regular Member
- Posts: 1112
- Joined: February 28th, 2002, 2:01 am
- Location: vancouver
Re: Carbon fiber Tails.
Made by matrix...so they are going to leak. 
-
Custommx3
- Site Administrator
- Posts: 8391
- Joined: November 7th, 2000, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Lat 35.1N Lon -90W
- Contact:
Re: Carbon fiber Tails.
FYI, MAtrix racing doesnt make Anything, NO altezzas are made by them at all, ALL of the mx-3 altezzas are made by one company, distributed by others. Just an FYI.
-
atlantamx3
- Supporting Member
- Posts: 2888
- Joined: June 2nd, 2001, 2:01 am
- Location: Kennesaw, Ga, USA
- Contact:
Re: Carbon fiber Tails.
<blockquote><font size="1" face="Verdana, Arial">quote:</font><hr>Originally posted by monstar-mx-3:
Made by matrix...so they are going to leak. <hr></blockquote><p>And, FYI, It s super easy to seal them up.<p>I used clear "ATV" Sealant on mine... and it works awesome.<p>6 Dabs of sealant on each one and boom... its done. No leak, no worries!
Made by matrix...so they are going to leak.
<hr></blockquote><p>And, FYI, It s super easy to seal them up.<p>I used clear "ATV" Sealant on mine... and it works awesome.<p>6 Dabs of sealant on each one and boom... its done. No leak, no worries!
-
mitmaks
- Senior Member
- Posts: 8704
- Joined: September 10th, 2001, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Spokane, WA
- Contact:
Re: Carbon fiber Tails.
or better yet is to find something functional for your car instead of something that every civic has, in my town even grannies put on altezzas lmao. Something like short shifter would be better buy, and at same price. I expect product to be fully functional and not needing any work done to it, especially when youre paying $150 and up for damn things, id expect them to be of better quality....aftermarket body parts suck.
Magnum s/s lines, strut bars, carbon fiber bezel, indiglow gauge, Sony Xplod, inverted c/f hood, SRD lower tie bar '93 GS SE '95 Cobra SVT #2722 '68 Charger R/T 440
http://www.cardomain.com/id/mitmaks
http://www.cardomain.com/id/mitmaks