MX-3.com

I am selling Klze Curved neck 2.5v6 with an Lsd transmition. Complete with headers thermo spacers Fidanza flywheel act 6 puck clutch kit unused fuel pump and fuel pressure regulator. Engine has new timing belt front main seal rear main seal, camshaft seals and valve cover gaskets and kl36 ecu for ...

I banged out my mx so now i have to get rid of the car but i have a couple of things that can be sold any body can also come and pick the parts up.

LSD Tranny 550+shipping

act clutch kit has about 2000 miles on it 6 puck 300+shipping

Fidanza 9 pound flywheel 220+shipping

SS Autochrome ...

I banged out my mx so now i have to get rid of the car but i have a couple of things that can be sold any body can also come and pick the parts up.

LSD Tranny 550+shipping

act clutch kit has about 2000 miles on it 6 puck 300+shipping

Fidanza 9 pound flywheel 220+shipping

SS Autochrome headers ...

I got bad news fellas I banged out my mx on the highway and the front end is almost unfixable. I found another mx3 but its the 4 banger. I need to know what needs to be done to take all that i put in the gs ( KLZE LSD tranny) and put it in the 4 banger. I am planning on having both so that i can ...

What alternator did you guys use when you did the ZE swap. Did you use the one from the k8 or the one from the ZE. I am having bad charging problems. I have the altenator of the K8 on, because the millinia altenator connector looked different, but i could be wrong and I cant check it now cause the ...

The car idles normal around 650-700 rpm and then when warmed up it starts to rise up and down from 1000-1500 rpm. And also it seems as if i have a misfire. Any ideas on the weird idle

http://img75.photobucket.com/albums/v227/Merlinmx3/electronique/SHEM_ECU2.jpg

Cut that wire :D It is coming out of the medium sized (22 wires) plug going into your ECU and the diagram is as if you were looking into the plugs on the ECU (wires are coming towards you).

I would cut it, but the ...

The wiring harness from my 1992 GS harness does not match the colors of the wiring diagram that was given on the site. I checked it and i cant find out the wire to cut to remove the speed limiter. If anyone has any idea on which wire to cut please let me know. I used the stock GS k8 harness on the ...

I got the cable off the throttle bod, but I dont know how to remove it off the pedal to take it out of the car and inspect it. I can't unhook it to get it off. So if any body has a clue drop me some knowledge. Thanks

When I turned the car on last night it started and immediately it reved all the way like full throttle and then i turned it off. Any ideas i looked at the throttle body and its not closed all the way. I closed and the car stopped doing it. When i tried to put my foot on the pedal, it felt like it ...

Well I changed my timing belt on saturday. The car runs fine. It was not that bad of a job. It only took about 3 hours. Thanks for the help peoples.

what is the easiest way to change the timing belt on our ZE engines while they are in the car. If any ideas please share

I checked this morning to se if the cams were spining and no spin so now I have to get the car towed to the shop. Thanks peoples for your input

Backround information, i was driving on the highway and the car started to hesitate alittle why accelerating, but it was doing it before and when i checked for spark it was very weak. So while driving the car just cut off and would start back up since.
all i did was change the distributor the rotor ...

I change the distributor and the car still wont start. The mass airflow sensor got a little banged around when i hit a bump on the starter. Any body think that the car will not give spark if the maf is not working properly. I have run out of Ideas