turbo feed kit

A Forum For All Forced Induction Systems Topics Such As Turbos, Superchargers and Nitrous Oxide.
Post Reply
mazdaguy25
Junior Member
Posts: 16
Joined: May 9th, 2011, 12:36 am
antispam: ~SPAM*SUX~

turbo feed kit

Post by mazdaguy25 »

Hey guys I am upgrading my turbo got a 57 trim t3/t4 and I need the right feed line kit and need a link to everything I need so I don't blow the new turbo up. If anyone could help me out that would be great thanks.
User avatar
Josh
Supporting Member
Posts: 3432
Joined: April 18th, 2002, 2:01 am
Location: Washington state
Contact:

Re: turbo feed kit

Post by Josh »

Like this easy Ebay search for a t3/t4 turbo feed kit found?

http://www.ebay.com/itm/T3-T4-T3-T4-T70 ... 33&vxp=mtr
mazdaguy25
Junior Member
Posts: 16
Joined: May 9th, 2011, 12:36 am
antispam: ~SPAM*SUX~

Re: turbo feed kit

Post by mazdaguy25 »

Ok thanks but was talking about everything even the bolt that goes into are block.
RobMinhas
Regular Member
Posts: 1614
Joined: November 5th, 2011, 8:32 pm
antispam: ~SPAM*SUX~
Location: Calgary, Alberta

Re: turbo feed kit

Post by RobMinhas »

What engine do you have?

And are the feed lines from ebay good quality? I've got a gt28 that I need all new fittings for, might try to find a complete set of feed lines and banjo bolts and stuff.
Daninski wrote:This is my MX3. There are many like it, but this one is mine. My MX3 is my best friend. It is my life. I must master it as I master my life. My MX3, without me, is useless. Without my MX3, I am useless. I must fire up my MX3 true. I must drive straighter than any Honda driver who is trying to own me. I must own him before he owns me.
mazdaguy25
Junior Member
Posts: 16
Joined: May 9th, 2011, 12:36 am
antispam: ~SPAM*SUX~

Re: turbo feed kit

Post by mazdaguy25 »

1.8 dohc bp motor
User avatar
Josh
Supporting Member
Posts: 3432
Joined: April 18th, 2002, 2:01 am
Location: Washington state
Contact:

Re: turbo feed kit

Post by Josh »

All you do is tap into the back of the block where the oil pressure sensor is. So a T fitting with two male sides and one female. Then buy like 18'' long SS braided line. and done.

Or find BPT hard lines from someone. Use whatever the turbo manufacture recommends.
mazdaguy25
Junior Member
Posts: 16
Joined: May 9th, 2011, 12:36 am
antispam: ~SPAM*SUX~

Re: turbo feed kit

Post by mazdaguy25 »

Y would i tap into the back when the oil is up front on are motors. I am asking for the right stuff to use the line up front and that gives my urbo the right amount of oil.
User avatar
marcdh
Regular Member
Posts: 1460
Joined: July 26th, 2006, 3:54 pm
Location: Belfast -Northern Ireland
Contact:

Re: turbo feed kit

Post by marcdh »

1/8 bspt thread for the ports on the head. Not sure how good the supply up top is.
AZ-3 1498cc Turbo! EVO 8 turbo and manifold, 5 stud swap, SSR Type C, DIYPNP seq Megasquirt
Mx-3 2.5 V6 Turbo 291 BHP 251 lbft @ 8psi - Retired due to rust and back at uni
View Worklog
Image
User avatar
Josh
Supporting Member
Posts: 3432
Joined: April 18th, 2002, 2:01 am
Location: Washington state
Contact:

Re: turbo feed kit

Post by Josh »

mazdaguy25 wrote:Y would i tap into the back when the oil is up front on are motors. I am asking for the right stuff to use the line up front and that gives my urbo the right amount of oil.

Aww see now we are getting somewhere.... You want OE BPT hard lines!? YES?

Your best bet is to find them in club protege used. I am pretty sure I have a set laying around. AND FYI there is just as much oil pressure on the back as there is the front fitting. And it is not doing it "wrong" by tapping the rear, most people do. It is easy, and away from the exhaust unlike the OE port on the front. The OE hardware will only fit a IHI VJ14, VJ11, VJ20 or VJ26. It could be adapted to fit others. I have run a VF10 and a VF12 as well. I understand what you are saying about doing it "right" but it is not as critical as I think, you, think it is.
Post Reply

Return to “Forced Induction”