how to run dual exhaust on mx-3
how to run dual exhaust on mx-3
Lets see how you ran your dual exhaust on your mx-3, or the best way to run it!! I have a bumper with dial cutouts that is why i am going to be running duals!!!
- RS_OBD'oh_2
- Senior Member
- Posts: 2400
- Joined: April 9th, 2007, 1:26 pm
- Location: Calgary, AB
Re: how to run dual exhaust on mx-3
I know this is not helpful... but why add extra weight and cost for no gain? I know it'll look cool and what-not. At least tell me it's a v6.
- Ryan
- Senior Member
- Posts: 7199
- Joined: April 7th, 2008, 1:06 pm
- antispam: ~SPAM*SUX~
- Location: Manitoba
Re: how to run dual exhaust on mx-3
No way... make a custom header for the 4 cyl, and run 1" dual all the way back. I should, just for shits and giggles.
on a more serious note, why not run single, and then get a muffler that splits it?
on a more serious note, why not run single, and then get a muffler that splits it?
Now with Moderator power!
Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped.
Feedback
Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped.
Feedback
Re: how to run dual exhaust on mx-3
i wonder what a infiiti g35 exhaust would look like on an mx3
- RS_OBD'oh_2
- Senior Member
- Posts: 2400
- Joined: April 9th, 2007, 1:26 pm
- Location: Calgary, AB
Re: how to run dual exhaust on mx-3
make sure that there is even room to mount a muffler widthwise. I believe the gas tank will be an issue. So, I'm guessing that the g35 exhaust would look like it's hitting the ground.
Re: how to run dual exhaust on mx-3
I wouldnt worry so much about the gas tank.
The spare tire well on the other hand.
If you get creative with a hammer.
Or a welder and a cut off tool just remove it completley.
The spare tire well on the other hand.
If you get creative with a hammer.
Or a welder and a cut off tool just remove it completley.

92' Rs-t b6t/De - RIP
93' Rs-t BPT - Sold
03' WRB wrx Wagon - Current
93' Rs-t BPT - Sold
03' WRB wrx Wagon - Current
Re: how to run dual exhaust on mx-3
you called it right... i had to get rid of my spare tire well to fit the duals. did it for the same reason as the OP.. just to match the rear bumper and complete the overall look. someone else on here didn't have to, they just managed.. but that was with a stock bumpernos92mx3 wrote:I wouldnt worry so much about the gas tank.
The spare tire well on the other hand.
If you get creative with a hammer.
Or a welder and a cut off tool just remove it completley.
- Nd4SpdSe
- Senior Member
- Posts: 11213
- Joined: May 25th, 2002, 2:01 am
- Location: Québec City, Quebec, Canada
- Contact:
Re: how to run dual exhaust on mx-3
I wouldn't. It just an expensive and complicated cosmetic modifiction that adds weight and will decrease performance.
1992 Mazda Mx-3 GSR - 2.5L KLZE : Award Winning Show Car & Race Car ['02-'09] (Retired)
2004 Mazda RX-8 GT - Renesis Wankel : LS3 Coils, BHR Mid-Pipe + Falken RT-615K 245/40r18
2011 Mazda Mazda2 GS - 1.5L Manual : Yozora Edition (1 of 500)
2003 Nissan Xterra SE - 4x4 Supercharged : 2" Body Lift, 4" Suspension Lift & 33" MTR Kevlar
2001 Nissan Frontier SE - The Frontrailer : Expedition/Off-Road Trailer Project
2004 Mazda RX-8 GT - Renesis Wankel : LS3 Coils, BHR Mid-Pipe + Falken RT-615K 245/40r18
2011 Mazda Mazda2 GS - 1.5L Manual : Yozora Edition (1 of 500)
2003 Nissan Xterra SE - 4x4 Supercharged : 2" Body Lift, 4" Suspension Lift & 33" MTR Kevlar
2001 Nissan Frontier SE - The Frontrailer : Expedition/Off-Road Trailer Project
- fowljesse
- Supporting Member
- Posts: 5676
- Joined: March 17th, 2006, 2:59 pm
- Location: portland, OR
- Contact:
Re: how to run dual exhaust on mx-3
I agree, but posted up some useful info on the same topic not long ago, that you should know, if you're going to do this right, and don't want to lose power. Also, you should research as much as you can about it.
'93 GS - P&P DE w/ ZE exh. cams/ pistns, KLG4 IM, 65mm TB, MSnS, Phenos, K&N RAI, UDP, Grnd wires, rear batt, filld MM, torq strt, TWM short shftr, Exedy, Lng tube hdrs 2.5" Side exhaust, H&R sprngs, Poly bushngs, strutbars, Alum. crss mmber&tiebar, 22mm swybar, solid links, Direzzas, leather int, Alpine 9805 stereo & alrm, keyless entry, 10 Boston Accoustics spkrs, Prjectrs, Blaster2, CF hood, FG hatch, Lexan
-
- Regular Member
- Posts: 162
- Joined: August 31st, 2008, 12:40 pm
- Location: Burlington, Ontario
- Contact:
Re: how to run dual exhaust on mx-3
just curous, how much roughly would it cost to get an exhaust done from the converter to muffler?? muffler included in purchse.
another note what would be a nice sounding muffler, not too loud. looking for more of a quite racing muffler. (magnaflow?)
another note what would be a nice sounding muffler, not too loud. looking for more of a quite racing muffler. (magnaflow?)
-
- Regular Member
- Posts: 156
- Joined: May 19th, 2005, 4:11 pm
- Location: The netherlands ( europe)
Re: how to run dual exhaust on mx-3
here's mine...
soon to be modified as i am getting tired of 2 big exhausts... going a bit smaller just for the more stock look...
don't mind the rust... the mx was sitting for more then a couple of months outside as we where swapping the ZE in..



soon to be modified as i am getting tired of 2 big exhausts... going a bit smaller just for the more stock look...
don't mind the rust... the mx was sitting for more then a couple of months outside as we where swapping the ZE in..



2.5L KLZE engine, CF hood, Postert frontbumper, kmax skirts, custom diffusor..
MY RIDE:
http://www.mazdamx-3.nl/members/member_show.php?id=102
MY RIDE:
http://www.mazdamx-3.nl/members/member_show.php?id=102