Cracks in bumpers- fixable or F'd?

A forum for Appearance Discussions. (Exterior, Body Kits, & Interior)
Post Reply
Buckminster
Regular Member
Posts: 66
Joined: September 28th, 2002, 2:01 am
Location: Kenora
Contact:

Cracks in bumpers- fixable or F'd?

Post by Buckminster »

The bumpers have some cracks in them, can they be repaired somehow or do they have to be replaced? Looks like it took a low speed bump on the front right corner and the area around the license plate is all spider webbed with cracks.
What is the price of a good scrap yard bumper I wonder.
MX-3 SE project car.
mazdamx3freak
Regular Member
Posts: 245
Joined: March 21st, 2005, 9:51 pm
Location: zephyrhills, florida

Re: Cracks in bumpers- fixable or F'd?

Post by mazdamx3freak »

yes most use bondo or fiberglass but as we all know it WILL crack again and maybe worse. A good thing to do is use a plastic welder and weld the cracks closed. A new or j/y bumper will cost you around $60 - $300+ usd .....plastic welder $30 - $80 usd.
User avatar
Ryan
Senior Member
Posts: 7199
Joined: April 7th, 2008, 1:06 pm
antispam: ~SPAM*SUX~
Location: Manitoba

Re: Cracks in bumpers- fixable or F'd?

Post by Ryan »

Mine is like that a little too, I think it is only the paint. The cracks don't seem to go through at all, and it still seems stable.

Since my car looks like a shite box, I'm leaving mine for now, but I'll check back here for what you did :)
Now with Moderator power!

Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped.
Feedback
User avatar
marcdh
Regular Member
Posts: 1460
Joined: July 26th, 2006, 3:54 pm
Location: Belfast -Northern Ireland
Contact:

Re: Cracks in bumpers- fixable or F'd?

Post by marcdh »

From my experience the stock bumpers don't crack easily, but the primer/paint/lacquer layer does. Hard to tell without pics but it might be fine underneath. The one time mine did crack on my, I used fibreglass... it's cracked again :roll:
AZ-3 1498cc Turbo! EVO 8 turbo and manifold, 5 stud swap, SSR Type C, DIYPNP seq Megasquirt
Mx-3 2.5 V6 Turbo 291 BHP 251 lbft @ 8psi - Retired due to rust and back at uni
View Worklog
Image
User avatar
Daninski
Supporting Member
Posts: 7055
Joined: June 18th, 2007, 10:51 am
Location: Trenton ON.

Re: Cracks in bumpers- fixable or F'd?

Post by Daninski »

If your cars been painted they may not of put a flexer in the paint for the bumpers so when it got bumped the paint cracks. Drop by a body shop and ask them, I went to 3 different shops to ask about a certain repair I needed to do. I got three different answers, all good.
2004 Subaru WRX Silver, stage 2, minty interior.
2002 Subaru WRX Blue, SOLD (best E test numbers I've ever seen)
94 MX-6. Sold
92 GS KLZE 5 Speed
96 GS 5 speed, KLZE, Sold
95 GS Minty Shape Sold
92 GS Sold
92 GS Parts Car scrapped.
Feedback viewtopic.php?f=37&t=66348" onclick="window.open(this.href);return false;
7477th member.

I know you believe that you understand what you think I said but I'm sure you realize that what you heard is not what I meant.
Buckminster
Regular Member
Posts: 66
Joined: September 28th, 2002, 2:01 am
Location: Kenora
Contact:

Re: Cracks in bumpers- fixable or F'd?

Post by Buckminster »

These are full fledged cracks- probably from a bump or two. I know where I can get some Junk yard bumpers but I gotta say taking them off seems like a pile of work. Does the welding work very well I wonder? I will bring it around to some shops and get their view.
MX-3 SE project car.
User avatar
Ryan
Senior Member
Posts: 7199
Joined: April 7th, 2008, 1:06 pm
antispam: ~SPAM*SUX~
Location: Manitoba

Re: Cracks in bumpers- fixable or F'd?

Post by Ryan »

Taking off the bumpers is maybe a 5 minute job :) One in each wheel well where it meets the fender(mine are phillips/8mm), one right beneath the bumper holding the corners steady(push plug/clip), two behind each signal marker(10mm), two under the hood(10mm), and either two more under the hood(10mm) or 4 screws(phillips) under the hood out of the bumper. Voila.
Now with Moderator power!

Black '93 BP RS - wrecked, parted, scrapped.
Green GS - Sold.
Black GS - Summer DD/Race car - Fancy KLZE
Red GS - K8-ATX -> MTX-KLDE - Frakencar. Scrapped
White GS - Rusty. Parts. Scrapped
1997 BMW M3 - my summer baby
2002 BMW 325Xi - sold
2003 Forester Xti - EJ20K swapped.
Feedback
projectzemx3
Regular Member
Posts: 1083
Joined: August 23rd, 2008, 12:09 am
Location: Beamsville.

Re: Cracks in bumpers- fixable or F'd?

Post by projectzemx3 »

my rs was like that with the spider webs and it was just the paint from where it had a minor impact long ago. my gs has a nasty split in it. i plan on getting a different one before paint.
NEED PARTS INSTALLED? PM ME!
Image
User avatar
fowljesse
Supporting Member
Posts: 5676
Joined: March 17th, 2006, 2:59 pm
Location: portland, OR
Contact:

Re: Cracks in bumpers- fixable or F'd?

Post by fowljesse »

Yeah, fix it from the inside. Your Auto paint/ body supplier will have the stuff.
'93 GS - P&P DE w/ ZE exh. cams/ pistns, KLG4 IM, 65mm TB, MSnS, Phenos, K&N RAI, UDP, Grnd wires, rear batt, filld MM, torq strt, TWM short shftr, Exedy, Lng tube hdrs 2.5" Side exhaust, H&R sprngs, Poly bushngs, strutbars, Alum. crss mmber&tiebar, 22mm swybar, solid links, Direzzas, leather int, Alpine 9805 stereo & alrm, keyless entry, 10 Boston Accoustics spkrs, Prjectrs, Blaster2, CF hood, FG hatch, Lexan
Post Reply

Return to “Appearance”