Autocross
- ElectricEnergy
- Regular Member
- Posts: 489
- Joined: August 15th, 2006, 12:37 am
- Location: Saskatoon SK, Canada
Autocross
Well, I went to my first autoX meet today. Damn that was fun. You guys shoulda been there.
I definitely need more practice. I knocked over lots of cones. I am very happy with the mx-3s handling though. Very over steer happy for a front wheel drive car.
I think I need to get some good racing tires too. These all seasons don't get much traction.
I think one of my friends got some good pictures of my car on the track. I'll try to get them posted up here soon.
I definitely need more practice. I knocked over lots of cones. I am very happy with the mx-3s handling though. Very over steer happy for a front wheel drive car.
I think I need to get some good racing tires too. These all seasons don't get much traction.
I think one of my friends got some good pictures of my car on the track. I'll try to get them posted up here soon.

KL-ZE Swap - OBX SS Headers - 2.5" Exhaust - Falken Azenis Tires - H&R Springs - ZX-2 Struts - CAI - Front & Rear Tower Bar - AWR Motor Mounts - 100hp wet shot (yet to be tested)
- ElectricEnergy
- Regular Member
- Posts: 489
- Joined: August 15th, 2006, 12:37 am
- Location: Saskatoon SK, Canada
Pictures just got uploaded. Check them out here:
http://forum.ssccracing.org/viewtopic.php?t=4041
I'm about 3/4 the way down the page. I didn't do very well, came in 21st out of 27. But I managed to shave at least a couple seconds off my time during the fun runs once I got used to it. So I'll probably do better next time.
I definitely encourage you guys to come to a few meets. It is a blast!
http://forum.ssccracing.org/viewtopic.php?t=4041
I'm about 3/4 the way down the page. I didn't do very well, came in 21st out of 27. But I managed to shave at least a couple seconds off my time during the fun runs once I got used to it. So I'll probably do better next time.
I definitely encourage you guys to come to a few meets. It is a blast!

KL-ZE Swap - OBX SS Headers - 2.5" Exhaust - Falken Azenis Tires - H&R Springs - ZX-2 Struts - CAI - Front & Rear Tower Bar - AWR Motor Mounts - 100hp wet shot (yet to be tested)
- mr1in6billion
- Supporting Member
- Posts: 961
- Joined: August 28th, 2005, 9:06 pm
- Location: Fog City
Your time isn't important. The fact that your time went down is. That's why it's called Solo. Considering you're a novice using a fairly underpowered car I'd say you did pretty well.ElectricEnergy wrote:I didn't do very well, came in 21st out of 27. But I managed to shave at least a couple seconds off my time during the fun runs once I got used to it.
- ElectricEnergy
- Regular Member
- Posts: 489
- Joined: August 15th, 2006, 12:37 am
- Location: Saskatoon SK, Canada
Yeah your right.
I actually felt that my car had enough power for the course we were on. I don't think a whole bunch more acceleration would have made as big of a difference as some good tires and suspension setup.
I actually felt that my car had enough power for the course we were on. I don't think a whole bunch more acceleration would have made as big of a difference as some good tires and suspension setup.

KL-ZE Swap - OBX SS Headers - 2.5" Exhaust - Falken Azenis Tires - H&R Springs - ZX-2 Struts - CAI - Front & Rear Tower Bar - AWR Motor Mounts - 100hp wet shot (yet to be tested)
- mr1in6billion
- Supporting Member
- Posts: 961
- Joined: August 28th, 2005, 9:06 pm
- Location: Fog City
- PATDIESEL
- Senior Member
- Posts: 4476
- Joined: August 13th, 2001, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Atlanta, GA.
Good lord, it looks like you are about to flip over.
Some newer shocks should help. I love the AutoX too. This is also my first year and I'm doing my second track this Saturday. Grats and drag as many of the Canook MXers with you as you can. The tech inspector told me last time "Damn, there has been a MX-3 explosion this year, what are there like 5 of you now". There are probably more MX-3s in the Atlanta region SCCA now then any other car, thanks in whole to all us MOCA members driving at them, hehehe.

Some newer shocks should help. I love the AutoX too. This is also my first year and I'm doing my second track this Saturday. Grats and drag as many of the Canook MXers with you as you can. The tech inspector told me last time "Damn, there has been a MX-3 explosion this year, what are there like 5 of you now". There are probably more MX-3s in the Atlanta region SCCA now then any other car, thanks in whole to all us MOCA members driving at them, hehehe.

ZE -strait neck,headers,2.5 exhaust,pheno spacers,lower cross member,GC coils,MS struts,Brembo slotted rotors,filled MS mounts,SS brake/clutch lines, CAI,to rear bat reloc,Hella headlamps,Hella DE fogs 180WHP
- atlantamx3
- Supporting Member
- Posts: 2888
- Joined: June 2nd, 2001, 2:01 am
- Location: Kennesaw, Ga, USA
- Contact:
- ElectricEnergy
- Regular Member
- Posts: 489
- Joined: August 15th, 2006, 12:37 am
- Location: Saskatoon SK, Canada
Hehe, yep it is. I obviously can't take credit for it... I don't actually know who took it. :p
Struts are on the shopping list. My new springs should be here on Friday. I wish I could put them in right away but its going to be a while until my struts get here.
I think that picture was taken about a millisecond before I spun out, I took that slalom WAY too fast.
I am definitely addicted now, I'm really looking forward to the next meet. Its on the 15th for all you local guys. Vanished! I expect you to be there. See if all that extra power does you any good.
Struts are on the shopping list. My new springs should be here on Friday. I wish I could put them in right away but its going to be a while until my struts get here.
I think that picture was taken about a millisecond before I spun out, I took that slalom WAY too fast.

I am definitely addicted now, I'm really looking forward to the next meet. Its on the 15th for all you local guys. Vanished! I expect you to be there. See if all that extra power does you any good.


KL-ZE Swap - OBX SS Headers - 2.5" Exhaust - Falken Azenis Tires - H&R Springs - ZX-2 Struts - CAI - Front & Rear Tower Bar - AWR Motor Mounts - 100hp wet shot (yet to be tested)
- PATDIESEL
- Senior Member
- Posts: 4476
- Joined: August 13th, 2001, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Atlanta, GA.
It won't. AtlMX3 has 120 crank HP and beats jaydog5678 who has a 300 WHP BP-t. lol- we rag him hard for loosing to a MX w/ half his power and less suspension work.

ZE -strait neck,headers,2.5 exhaust,pheno spacers,lower cross member,GC coils,MS struts,Brembo slotted rotors,filled MS mounts,SS brake/clutch lines, CAI,to rear bat reloc,Hella headlamps,Hella DE fogs 180WHP
- ElectricEnergy
- Regular Member
- Posts: 489
- Joined: August 15th, 2006, 12:37 am
- Location: Saskatoon SK, Canada
Oh yah! I'll be there....my suspension should keep me a head of you, but you've got more experience. I expect to be terrible the first couple runs, but i hope not hahaha. May 15th, i'll be there...new tire rod and and control arm with bushings need to be in first. Can't wait.
Oh, ikiller pic by the way.
Oh, ikiller pic by the way.
- ElectricEnergy
- Regular Member
- Posts: 489
- Joined: August 15th, 2006, 12:37 am
- Location: Saskatoon SK, Canada
I did pretty crappy on my first tries.... Spun out on 3 of 7 runs. But I can already tell that my overall driving skill has improved. It really helps you get an idea of exactly what your car is capable of.
We should meet up an hour or two before the event to get the cars ready and such. You have to ramp the tire pressure way up to avoid wrecking them.
We should meet up an hour or two before the event to get the cars ready and such. You have to ramp the tire pressure way up to avoid wrecking them.

KL-ZE Swap - OBX SS Headers - 2.5" Exhaust - Falken Azenis Tires - H&R Springs - ZX-2 Struts - CAI - Front & Rear Tower Bar - AWR Motor Mounts - 100hp wet shot (yet to be tested)
- ElectricEnergy
- Regular Member
- Posts: 489
- Joined: August 15th, 2006, 12:37 am
- Location: Saskatoon SK, Canada
- PATDIESEL
- Senior Member
- Posts: 4476
- Joined: August 13th, 2001, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Atlanta, GA.
What do you put the pressure at? I run 35psi b/c the air temp in the tires will get much hotter and expand, making more pressure. You can also chalk the tire edge to make sure you are getting a full contact patch without any sidewall roll. I think I migh try that at the next event in June.

ZE -strait neck,headers,2.5 exhaust,pheno spacers,lower cross member,GC coils,MS struts,Brembo slotted rotors,filled MS mounts,SS brake/clutch lines, CAI,to rear bat reloc,Hella headlamps,Hella DE fogs 180WHP