new sway bar for the mx-3!!!

happyclown · Post by **happyclown** » October 31st, 2005, 1:13 pm

So the weekend was beautiful up here. Did you have any luck gettin the bar in?

neutral · Post by **neutral** » November 1st, 2005, 4:05 am

happyclown wrote:So the weekend was beautiful up here. Did you have any luck gettin the bar in?

Nah not yet.

Weather turned great here too but I got badly jammed up Sunday with troubleshooting some data network probs for a project at my job and now have also caught a mutha big nasty head cold too.

Have had the new bar for a week already and don't wanna let too much time go by, if I end up having to return it for poor fitment. Gonna try to look at it before I leave for work, either early one morning later this week, after sun-up, or if necessary, I'll get out there with a flashlight one evening.

happyclown · Post by **happyclown** » November 3rd, 2005, 4:44 pm

Damn, everyone around here's been getting a nasty head cold, nothin too serious but just enought to make them worthless

...

just kiddin...

good luck with it when you get around to it.

neutral · Post by **neutral** » November 4th, 2005, 5:46 pm

I still have the headcold but a particularly brutal workweek is finally over and I'm gonna check the fitment for this thing in the a.m. no matter what. Weatherdude is calling for sunny 70's tomorrow here and might not see those temps again for 6 months.

jschrauwen · Post by **jschrauwen** » November 4th, 2005, 6:06 pm

happyclown wrote:Damn, everyone around here's been getting a nasty head cold, nothin too serious but just enought to make them worthless

Me too .... sniff ... sniff ....

neutral wrote:I still have the headcold but a particularly brutal workweek is finally over and I'm gonna check the fitment for this thing in the a.m. no matter what. Weatherdude is calling for sunny 70's tomorrow here and might not see those temps again for 6 months.

Will be waiting on the post-mortem Jim ..... LOL

jschrauwen · Post by **jschrauwen** » November 5th, 2005, 1:28 pm

I'd say by now, Jim is elbow deep in fiddling with the sway bar, perhaps cursing a little as he goes along. Hope it's panning out Jim.

hppwdn · Post by **hppwdn** » November 7th, 2005, 6:50 pm

I'm anxious to find out the results too.

hppwdn · Post by **hppwdn** » November 12th, 2005, 8:37 am

Any results yet?

happyclown · Post by **happyclown** » November 17th, 2005, 11:33 am

must be a deadly procedure, everyone who attempted the fit is missing

what ever will we do

UPDATE

babyblueMX3 · Post by **babyblueMX3** » November 17th, 2005, 11:43 am

will I have to order it myself

j/k
cmon guys, couple of guys bought this bar and has it in their own hands. Someone must have found the time to install it

jschrauwen · Post by **jschrauwen** » November 17th, 2005, 6:46 pm

babyblueMX3 wrote:will I have to order it myself j/k
cmon guys, couple of guys bought this bar and has it in their own hands. Someone must have found the time to install it

I'm not even going to take it out of the box until Jim posts back. At least, for now.

hppwdn · Post by **hppwdn** » November 17th, 2005, 8:34 pm

I PM'd him, but haven't gotten a response.

hppwdn · Post by **hppwdn** » November 28th, 2005, 9:21 pm

So did this project just dissolve into nothing?

jschrauwen · Post by **jschrauwen** » November 29th, 2005, 4:04 pm

perhapsadingoatejim

Legato626 · Post by **Legato626** » November 30th, 2005, 9:00 pm

after this xmas i will get mine and see what the hell is wrong then find out.