
Nicest Body Kits?
Nicest Body Kits?
well hey guys, im a newbie here. i de like to start modding out my mx-3 and i was lookin at some body kits. i have found that i like the fx conbat full body kits the best, however i have definatly seen some other sweet ones. so i was wondering what full body kits that you guys would recomend that are relatively inexpensive (under 600) if you guys could tell me what you had, where to get it, and even post some pics of them, that would be awesome. thanks a lot guys, i hope to learn alot about my mx3 on this site 

- mitmaks
- Senior Member
- Posts: 8704
- Joined: September 10th, 2001, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Spokane, WA
- Contact:
i like drift but ive got fx front
Magnum s/s lines, strut bars, carbon fiber bezel, indiglow gauge, Sony Xplod, inverted c/f hood, SRD lower tie bar '93 GS SE '95 Cobra SVT #2722 '68 Charger R/T 440
http://www.cardomain.com/id/mitmaks

http://www.cardomain.com/id/mitmaks

Yeah im wit Mitmaks on that one. Once again I will say the drift bumper hangs lower than the rest of the kit and it looks funky. Do a search on cardomain to check out some mx-3's with kit on em, and if you want a decent kit check out http://www.cheapkitsdirect.com I swear these guys should just give me a free body kit for reccomending them so many times! 

93SE-KLDE Theres a big peice of metal inside my other peice of metal now...weird???


-
- Senior Member
- Posts: 2220
- Joined: October 17th, 2004, 2:01 am
- Location: SLC, Utah
Look up the BC2 bodykit. It looks pretty damn great on the MX3.
Also, you might like the Mazdaspeed Bodykit as well.
Also, you might like the Mazdaspeed Bodykit as well.
2008 Mazda 3
1993 MX3 GS
KLZE, Fidanza flywheel, KL31 CAMs, South Bend Stage I Clutch, Pacesetter STS, SS AutoChromes, Magnaflow muffler, 2.25' Exhaust, CAI, Blaster Coil HEI, KLDE Valvetrain, 5 Speed Swap
1993 MX3 GS
KLZE, Fidanza flywheel, KL31 CAMs, South Bend Stage I Clutch, Pacesetter STS, SS AutoChromes, Magnaflow muffler, 2.25' Exhaust, CAI, Blaster Coil HEI, KLDE Valvetrain, 5 Speed Swap
- mitmaks
- Senior Member
- Posts: 8704
- Joined: September 10th, 2001, 2:01 am
- antispam: ~SPAM*SUX~
- Location: Spokane, WA
- Contact:
rear bumper looks Onderground to me...front and sides are fx...
maybe try protege5 bumper for mx3...or mazdaspeed just look around body kits and theres every style listed already
maybe try protege5 bumper for mx3...or mazdaspeed just look around body kits and theres every style listed already
Magnum s/s lines, strut bars, carbon fiber bezel, indiglow gauge, Sony Xplod, inverted c/f hood, SRD lower tie bar '93 GS SE '95 Cobra SVT #2722 '68 Charger R/T 440
http://www.cardomain.com/id/mitmaks

http://www.cardomain.com/id/mitmaks

-
- Senior Member
- Posts: 2220
- Joined: October 17th, 2004, 2:01 am
- Location: SLC, Utah
That back bumper would look much better if the gaps (where the exhaust goes) wasnt so wide.
It was made for 2 exhaust pipes to reach out on each side just incase you were curious
It was made for 2 exhaust pipes to reach out on each side just incase you were curious
2008 Mazda 3
1993 MX3 GS
KLZE, Fidanza flywheel, KL31 CAMs, South Bend Stage I Clutch, Pacesetter STS, SS AutoChromes, Magnaflow muffler, 2.25' Exhaust, CAI, Blaster Coil HEI, KLDE Valvetrain, 5 Speed Swap
1993 MX3 GS
KLZE, Fidanza flywheel, KL31 CAMs, South Bend Stage I Clutch, Pacesetter STS, SS AutoChromes, Magnaflow muffler, 2.25' Exhaust, CAI, Blaster Coil HEI, KLDE Valvetrain, 5 Speed Swap
I think its at least 3 inches higher than the fx sides. Someone correct me if i'm wrong. I think there was another thread about this and someone mentioned the MS front is actually a little higher than the stock bumper. If yer gonna put on extreme sides like that you'll need to get a pretty extreme front like the bc2 or combat
93SE-KLDE Theres a big peice of metal inside my other peice of metal now...weird???


- fry_81
- Regular Member
- Posts: 1898
- Joined: April 22nd, 2004, 2:01 am
- Location: Barrie, Ontario, Canada
- Contact:
ya the height difference is all too noticeable between the front and the sides with the MS.
1994 5spd GS Parts Car For Sale 800obo. e-mail for details. fry_81@hotmail.com
-
- Senior Member
- Posts: 2220
- Joined: October 17th, 2004, 2:01 am
- Location: SLC, Utah
I dont think that sounds good because the fx combat sideskirts dont go well with the front bumperhurd69 wrote:so how would this sound?
mazdaspeed front bumper
fx combat side skirts
onderground rear bumper
hood scoop
GTR or combat rear wing
does anyone have this setup or can anyone photoshoip this setup?
would they all line up with each other?
If you look at the very bottom of the front bumper and the sideskirts you will see why because the sideskirts have that "swirgly" kind of thing on the bottom.
As for the onderground rear bumper, I was thinking about this but I think the rear bumper from onderground is lower than the Mazda Speed front bumper. Try e-mailing them and ask them how much in length it is.
2008 Mazda 3
1993 MX3 GS
KLZE, Fidanza flywheel, KL31 CAMs, South Bend Stage I Clutch, Pacesetter STS, SS AutoChromes, Magnaflow muffler, 2.25' Exhaust, CAI, Blaster Coil HEI, KLDE Valvetrain, 5 Speed Swap
1993 MX3 GS
KLZE, Fidanza flywheel, KL31 CAMs, South Bend Stage I Clutch, Pacesetter STS, SS AutoChromes, Magnaflow muffler, 2.25' Exhaust, CAI, Blaster Coil HEI, KLDE Valvetrain, 5 Speed Swap