Re: UK Sam's 1.6 Turbo MX-3 project
Posted: January 15th, 2011, 5:34 am
because no-one has my imagination, mwhahahahahafillpereira wrote:That looks awesome, why hasnt this been done before lol
MX-3.com
The Worlds First and Largest Mazda MX-3 Forums
https://www.mx-3.com/phpbb3/
Sam's 1.6 MX-3- LT Turbo project.
Page 6 of 51
Re: UK Sam's 1.6 Turbo MX-3 project
Posted: January 26th, 2011, 12:48 pm
grill meshing the hole was a mare!
so instead the siliocon tubing has gone
around the bumper and new grill mesh
is being bought to go behind and fixed
to the back of the bumper.
in the meantime have started work
on a wind splitter made from 5mm plastic
also need to get a drivers side headlight
as mine has a crack, before I fit this lot up.
few more weeks waiting yet!
so instead the siliocon tubing has gone
around the bumper and new grill mesh
is being bought to go behind and fixed
to the back of the bumper.
in the meantime have started work
on a wind splitter made from 5mm plastic
also need to get a drivers side headlight
as mine has a crack, before I fit this lot up.
few more weeks waiting yet!
Re: UK Sam's 1.6 Turbo MX-3 project
Posted: January 26th, 2011, 2:28 pm
Your doing a great job. I look forward to seeing it on the car. 
Re: UK Sam's 1.6 Turbo MX-3 project
Posted: February 4th, 2011, 12:38 pm
should be on next weekend
Re: UK Sam's 1.6 Turbo MX-3 project
Posted: February 12th, 2011, 8:59 am
Re: UK Sam's 1.6 Turbo MX-3 project
Posted: February 12th, 2011, 9:41 am
I think it'd look pretty badass if you do the angry-eye mod too! 
Re: UK Sam's 1.6 Turbo MX-3 project
Posted: February 12th, 2011, 10:51 am
Turned out great, good job man
Re: UK Sam's 1.6 Turbo MX-3 project
Posted: February 12th, 2011, 10:58 am
No one over here does that anymore!Savin wrote:I think it'd look pretty badass if you do the angry-eye mod too!
Very pleased with it myself,
just need to 'flex' the splitter
down a bit with its support rods
Re: UK Sam's 1.6 Turbo MX-3 project
Posted: February 12th, 2011, 11:06 am
How about a custom headlamp with an airduct to complete the look?
Re: UK Sam's 1.6 Turbo MX-3 project
Posted: February 12th, 2011, 11:45 am
Very impressive. Great work and good vision.
Re: UK Sam's 1.6 Turbo MX-3 project
Posted: February 12th, 2011, 12:05 pm
This is my daily driver, so that would have to be 'tr5ackday special'Sleeper6 wrote:How about a custom headlamp with an airduct to complete the look?
thing.
Thanks Aaron, appreciate your comments
Re: UK Sam's 1.6 Turbo MX-3 project
Posted: February 18th, 2011, 12:13 pm
test fitted up my 25mm spacers.
located with 54.1 > 67.1 spigot ring
Too wide on the front without loads of negy camber
just inside with negy camber
going to have to arch roll or turn the spacers down a bit...to pass MOT laws
Rears are in, just!
wheels are 15 x 7 et35 195/50/15's btw
Took the fronts back off till I decide what to do with 'em
p.s. and please no spacer bashing I know the deal
located with 54.1 > 67.1 spigot ring
Too wide on the front without loads of negy camber
just inside with negy camber
going to have to arch roll or turn the spacers down a bit...to pass MOT laws
Rears are in, just!
wheels are 15 x 7 et35 195/50/15's btw
Took the fronts back off till I decide what to do with 'em
p.s. and please no spacer bashing I know the deal
Re: UK Sam's 1.6 Turbo MX-3 project
Posted: February 19th, 2011, 5:01 am
looks great man!
Re: UK Sam's 1.6 Turbo MX-3 project
Posted: February 20th, 2011, 4:20 am
Thanks Weede
She'll look even better if I can fuse these
new mirrors of mine to original base plates !
She'll look even better if I can fuse these
new mirrors of mine to original base plates !
Re: UK Sam's 1.6 Turbo MX-3 project
Posted: February 23rd, 2011, 12:50 pm
That looks Really good... its not like some of them that have holes everywhere and a massive one in the middle...