KL-ZE Turbo project by: Miguel - jeroentje.nl

A Forum For All Forced Induction Systems Topics Such As Turbos, Superchargers and Nitrous Oxide.
Post Reply
jeroentje_nl
Junior Member
Posts: 17
Joined: September 25th, 2002, 2:01 am
Location: The Netherlands

KL-ZE Turbo project by: Miguel - jeroentje.nl

Post by jeroentje_nl »

After 2 years hard driving with 100hp NOS shots (310hp) Miguel wanted this power all the time.. so it is time for a turbo !
So here we go

we are still working on a KL-ZE Turbo project. And hopefully getting it ready in a couple of weeks.

list of mods:

- KL-ZE Engine
- Ported
- bigger injectors
- Thermal spacers
- Probe turbo header
- T3 Hybrid Turbo
- 38mm Wastgate
- 3inch exhaust system
- Front mount intercooler
- Greddy blow of valve
- MAP-ECU fuel computer (vaf removed)
- Wideband

And some pictures :D
More pictures: http://www.jeroentje.nl/index.php?page= ... w&car_id=4

old KL-ZE engine
Image

engine is out now
Image

Time for sime polishing and spraying.
Image

Image

Image

Porting
Image

Image

This is how the engine look like now
Image

Image

Image

the engine back in the car
Image

Turbo and wastegate
Image

Turbo bold on the the header. (needs 12mm spacer)
Image

Making a little room for intercooler piping with plasma cutter
Image

changing the intercooler
Image

Image

Intercooler mounted
Image

Image
Top
User avatar
papa roached
Senior Member
Posts: 2761
Joined: December 10th, 2002, 2:01 am
Location: Montgomery, WVa

Post by papa roached »

looks nice and clean so far, like how you run the IC piping
93 MX-3 GS (collecting parts for Eunos Presso conversion), 94 626 Transmission (4.10 gears), KL31 camed KL-ZE, Millenia intake, Millenia TB, SSAutochrome V2 headers, Magnaflow cat, 2 1/4 in pipe, Top Speed Pro 1 muffler, 9lb Fidanza Flywheel, ACT clutch, Corksport SS clutch line, Corksport SS brake lines, Unorthadox UDP, 255 lph fuel pump, HEI mod, ghetto-charger intake, KL36 ECU, SRD transverse crossmember bushings, SRD shifter extention bushing, SRD crossmember, Corksport bronzoil shifter bushings, Brembo Crossdrilled and Slotted rotors, 15 inch Konig Heliums, ZX-2 S/R struts, Eibach lowering springs, OEM front strut bar, Ebay rear strut bar, BFGoodrich G-Force T/A KDWs

Parts needing installed: turbo kit from BB (if i ever get it), 9.0:1 CR Diamond pistons, 4340 forged H beam rods, C/J-Spec spoiler, Nissan red tops in KL rails
http://www.cardomain.com/id/blazejeremy
Top
User avatar
Dali
Supporting Member
Posts: 1621
Joined: January 28th, 2003, 2:01 am
antispam: No
Location: Williams lake, BC

Post by Dali »

man that looks good. :D
Top
User avatar
PATDIESEL
Senior Member
Posts: 4476
Joined: August 13th, 2001, 2:01 am
antispam: ~SPAM*SUX~
Location: Atlanta, GA.

Post by PATDIESEL »

!!HOT!! Nice work, it all looks really good. Now go race it a few times to dirty it up 8)
Image
ZE -strait neck,headers,2.5 exhaust,pheno spacers,lower cross member,GC coils,MS struts,Brembo slotted rotors,filled MS mounts,SS brake/clutch lines, CAI,to rear bat reloc,Hella headlamps,Hella DE fogs 180WHP
Top
User avatar
Custom_V6_Limited_SE
Regular Member
Posts: 508
Joined: October 11th, 2005, 12:58 pm
Location: Spring Hill, FL

Post by Custom_V6_Limited_SE »

:love: *drools profusely* O MY GOD. That is the best looking ZE I have ever seen. *drools some more* I didn't know it was possible to make it look so dang good. Great Work!!!

P.S. Have fun killing those skylines :)
'93 MX-3 GS SE:My Mods
Top
User avatar
XxantwawnxX
Regular Member
Posts: 1281
Joined: January 8th, 2005, 11:08 pm
Location: Newportnews VA

Post by XxantwawnxX »

Very nice! welcome to the boosted ZE club : P
Image

* * * * * * 92 Mx3 ZET, rear/front swaybars,srd crossmember,HKS SSQV,cold air,ZE with millinia mani and TB and 280cc injectors,INtrax springs with tokiko HP struts, Grounding kit, MotegiTrakLite wheels 17's at 14lbs each, MSnS Running fuel and spark,HEI mod,T3/To4E .60/.63 stage 3 turbine,3rd gen rx7 fuel pump, SSAC Headers/hotpipes ,38 ext tial wastegate, findanza flywheel, SBC TZ clutch/pressureplate,braille11pound battery/ magnum drilled F/R rotors,projectors, CXmotorsports almuminum intercooler.
Top
Slammed6
Regular Member
Posts: 965
Joined: January 14th, 2005, 5:34 am
Location: Oxnard, California

Post by Slammed6 »

That is beautiful work man...i like it.

Very clean....thats how i wanna do my intercooler if i go turbo.
***D-Tuned Custom KL MX-3 on Nitrous***
Top
User avatar
Steeb
Regular Member
Posts: 1897
Joined: June 29th, 2001, 2:01 am
Location: CA, USA
Contact:
Contact Steeb

Post by Steeb »

your motor looks very nice
Top
Post Reply

Return to “Forced Induction”