[FS] MX3 PARTS

blkmx3ze · Post by **blkmx3ze** » July 7th, 2005, 7:53 pm

Distributor, Battery, Alternator, Spark Plug Cables, Starter. Lowering Springs, Radiator, O2 Sensors, Engine Components, Hood, both fenders, trunk cover.(I have a full KlZE Swap) I am parting out a 92mx3GS no front bumper cover I got the the thing underneather the plastic bar you put the bumper cover on....Other sensors, and goodies also available....as i pull the off the car....pickup is perfered.....

bmwm3guy · Post by **bmwm3guy** » July 7th, 2005, 7:56 pm

post where you're from.. not that Im interested but ppl will ask.

blkmx3ze · Post by **blkmx3ze** » July 7th, 2005, 8:05 pm

sorry and thank you from waterloo/st jacobs Ontario.... 1 hr away from toronto....stock rims seats, full interior exept the driver side power switch..... water pump...complete car tranny doesnt go into third.....the rest of the parts I will pull out over the weekend/next week...

fry_81 · Post by **fry_81** » July 7th, 2005, 8:11 pm

what type of lowering springs are they?

blkmx3ze · Post by **blkmx3ze** » July 7th, 2005, 8:19 pm

Honestly they are yellow and drop the front and back by 1 75.... I got stock stuts on the front and newer ones on the back with about 10 000 k
I will try to find out the make of the springs

hppwdn · Post by **hppwdn** » July 7th, 2005, 9:10 pm

Also interested in the springs. I'm in Miami though so shipping could be a dealbreaker.

jschrauwen · Post by **jschrauwen** » July 7th, 2005, 9:44 pm

If your ZE was running a KL68 TB, I'll take that.

blkmx3ze · Post by **blkmx3ze** » July 7th, 2005, 10:05 pm

And I find that out how......its a curved neck intake manifold.....from an mx6 ZE i think...does that tell you anything or is there some sort of a marking

jschrauwen · Post by **jschrauwen** » July 7th, 2005, 10:25 pm

blkmx3ze wrote:And I find that out how......its a curved neck intake manifold.....from an mx6 ZE i think...does that tell you anything or is there some sort of a marking

That may tell me that the TB has the IAC (black round cylindrical part on the bottom of the TB) should be located to the right of the TB as you are looking at the (front) intake side. On the top of the TB should be some stampings of which you should see KL68 or maybe KL47. Refer to the TB depicted in attached millaj01 post;
http://www.mx-3.com/phpbb2/viewtopic.ph ... light=kl68

raidermaniac · Post by **raidermaniac** » July 7th, 2005, 10:27 pm

do u have the ecu for the ze?

blkmx3ze · Post by **blkmx3ze** » July 7th, 2005, 10:40 pm

KL 68 2R21 89 something and a long serial number
Intrax springs for those above

blkmx3ze · Post by **blkmx3ze** » July 7th, 2005, 10:46 pm

sorry no ecu sold it like 2 days ago to Jeffg from thornhill i think...sorry

blkmx3ze · Post by **blkmx3ze** » July 7th, 2005, 10:49 pm

I have all the sensors and the intake manifold for sale if anyone needs anything in that area and also PRM Cold Air Intake and Brospeed Header (I have yet to take the back off)

relisys_3200 · Post by **relisys_3200** » July 7th, 2005, 10:51 pm

blkmx3ze wrote:I have all the sensors and the intake manifold for sale if anyone needs anything in that area and also PRM Cold Air Intake and Brospeed Header (I have yet to take the back off)

I think fry was looking for some headers.

fry_81 · Post by **fry_81** » July 7th, 2005, 10:58 pm

ya i reallly need headers, shoot an offer, i will buy them.