[GI] CARBON FIBER HATCH BB
Author |
Message |
EZ_4_FUN
Supporting Member
Joined: April 02 2001, 2:01 AM Posts: 1026 Location: Toronto
|
 Re: [GI] CARBON FIBER HATCH BB
WHO HAS NOT YET RECEIVED THEIR HATCH?
_________________ OSKY 95 MX-3 GS ZE Turbo: MSnS-extra, AEM WB, Blitz boost controller, MSD 6A w/ Blaster2 Coil, ZE disty, Redtops @ 550, Walbro 255, Garrett T3/T04E 60 Trim w/ .63 A/R, 38mm Deltagate Mark II @4psi, FMIC, Apexi BOV, CM Dual friction, 4-6.25 Kickers, 2ch Alpine V12. That's Alll.
http://www.pakfeifertuning.com
|
September 28 2009, 3:47 PM |
|
 |
93vtecklr
Regular Member
Joined: March 23 2009, 12:10 AM Posts: 924 Location: Red Deer, Alberta
|
 Re: [GI] CARBON FIBER HATCH BB
Out of curiosity, did you only make enough for the BB? Or do you have any in stock?
_________________
 1993 Blaze Red SE, 17" blackie's, b+m sts, 45 deg 3" exh pipe/intake tube, K8ZE, aftmkt probe headers, magnaflow hi-cat, all 2.5" piping, magnaflow muffler. 1976 Datsun 620 p/u, full airride, Firestone 2600`s, 16ga fuel cell, Optima yellow top, AZ compressor, custom tubular frame with 9in step notch, 18" 100 spokes 1955 Willys Overland 4x4 P/U, '78 LT1 350 cu.in, fully restored.
|
September 28 2009, 6:34 PM |
|
 |
EZ_4_FUN
Supporting Member
Joined: April 02 2001, 2:01 AM Posts: 1026 Location: Toronto
|
 Re: [GI] CARBON FIBER HATCH BB
I can have them made on demand. Usually takes about 5 days to complete.
_________________ OSKY 95 MX-3 GS ZE Turbo: MSnS-extra, AEM WB, Blitz boost controller, MSD 6A w/ Blaster2 Coil, ZE disty, Redtops @ 550, Walbro 255, Garrett T3/T04E 60 Trim w/ .63 A/R, 38mm Deltagate Mark II @4psi, FMIC, Apexi BOV, CM Dual friction, 4-6.25 Kickers, 2ch Alpine V12. That's Alll.
http://www.pakfeifertuning.com
|
September 28 2009, 7:13 PM |
|
 |
93vtecklr
Regular Member
Joined: March 23 2009, 12:10 AM Posts: 924 Location: Red Deer, Alberta
|
 Re: [GI] CARBON FIBER HATCH BB
Thank you for the speedy reply!
_________________
 1993 Blaze Red SE, 17" blackie's, b+m sts, 45 deg 3" exh pipe/intake tube, K8ZE, aftmkt probe headers, magnaflow hi-cat, all 2.5" piping, magnaflow muffler. 1976 Datsun 620 p/u, full airride, Firestone 2600`s, 16ga fuel cell, Optima yellow top, AZ compressor, custom tubular frame with 9in step notch, 18" 100 spokes 1955 Willys Overland 4x4 P/U, '78 LT1 350 cu.in, fully restored.
|
September 28 2009, 7:21 PM |
|
 |
hgallegos915
Senior Member
Joined: June 19 2004, 2:01 AM Posts: 6451 Location: El Paso Tx U.S
|
 Re: [GI] CARBON FIBER HATCH BB
really? on demand? for the same BB price? WOW I know what Im getting myself this income tax/bonus season 
_________________ -hec
MX-3 w/ curved neck millenia klde, boosted @ 5 psi. /bov and wastegate are good!/ nitto drag radial/ gutted interior/ millenia red top injectors, vortech fmu/aem wideband/ all bolts ons/ Car put together 100% by me. Mechanic? who needs a mechanic? ew.. real men work on their own cars!
|
October 01 2009, 12:57 AM |
|
 |
Mooneggs
Forum Moderator
Joined: August 10 2005, 10:08 PM Posts: 6128 Location: Hillsboro, OR
|
 Re: [GI] CARBON FIBER HATCH BB
I finally test fitted my CF hatch to the car and it almost seems like it's just a tad too short in the back near the taillights... I believe this may be due to the placement of the bolts for the hinges... final fitment may be more exact... overall I am happy with it.
_________________ My Feedback 92 mx-3 gs klze 'race car' IP 15.05 @ 92.5mph 92 mx-3 gs klze 'daily driver' IP 14.55 @ 95.7mph http://www.cardomain.com/id/Mooneggs
|
March 06 2010, 1:27 AM |
|
 |
fowljesse
Supporting Member
Joined: March 17 2006, 3:59 PM Posts: 5676 Location: portland, OR
|
 Re: [GI] CARBON FIBER HATCH BB
Mine fits the back, but has a big gap on the very top  Also the side gaps aren't as close as OEM. I expect that it warped. It's good enough though! One would have to do a bit of adjusting, if it were for a showcar, but everything aftermarket has to be adjusted for a showcar.
_________________ '93 GS - P&P DE w/ ZE exh. cams/ pistns, KLG4 IM, 65mm TB, MSnS, Phenos, K&N RAI, UDP, Grnd wires, rear batt, filld MM, torq strt, TWM short shftr, Exedy, Lng tube hdrs 2.5" Side exhaust, H&R sprngs, Poly bushngs, strutbars, Alum. crss mmber&tiebar, 22mm swybar, solid links, Direzzas, leather int, Alpine 9805 stereo & alrm, keyless entry, 10 Boston Accoustics spkrs, Prjectrs, Blaster2, CF hood, FG hatch, Lexan
|
March 07 2010, 10:59 AM |
|
 |
Mooneggs
Forum Moderator
Joined: August 10 2005, 10:08 PM Posts: 6128 Location: Hillsboro, OR
|
 Re: [GI] CARBON FIBER HATCH BB
I just posted a few pics in my worklog... haven't actually put the finished product on my car yet but my hatch is "completed" viewtopic.php?f=46&t=59560&p=546661#p546661
_________________ My Feedback 92 mx-3 gs klze 'race car' IP 15.05 @ 92.5mph 92 mx-3 gs klze 'daily driver' IP 14.55 @ 95.7mph http://www.cardomain.com/id/Mooneggs
|
March 28 2010, 4:10 PM |
|
 |
Mooneggs
Forum Moderator
Joined: August 10 2005, 10:08 PM Posts: 6128 Location: Hillsboro, OR
|
 Re: [GI] CARBON FIBER HATCH BB
installed pics on the daily driver... viewtopic.php?f=46&t=59559&start=180
_________________ My Feedback 92 mx-3 gs klze 'race car' IP 15.05 @ 92.5mph 92 mx-3 gs klze 'daily driver' IP 14.55 @ 95.7mph http://www.cardomain.com/id/Mooneggs
|
April 21 2010, 1:05 AM |
|
 |
projectmx
Senior Member
Joined: December 07 2002, 3:01 AM Posts: 2165 Location: windsor, ontario
|
 Re: [GI] CARBON FIBER HATCH BB
wow man that looks beautiful, i hope i can eventually get my hands on one
_________________ ProjectMx My BP and AWD build thread Cardomain 93 Mx-3 GS with bp and GTR AWD system 93 Escort GT daily driving
|
April 21 2010, 7:25 AM |
|
 |
|
Who is online |
Users browsing this forum: Majestic-12 [Bot] and 0 guests |
|
You cannot post new topics in this forum You cannot reply to topics in this forum You cannot edit your posts in this forum You cannot delete your posts in this forum
|
|